Electronics-international FP-5L Manuale Utente

II 05069315/6/93Rev. I: 7/2/02Installation Instructions(FP-5 and FP-5L)Fuel Flow/Pressure2.5"2.5"3.65"Electronics International Inc. ®6

811. (FP-5L Only) Connect the RS-232 Output Line:Connecting the FP-5L Output Line to a compatible GPS unit allows the GPS unit to use the fuel datatr

913. Install the Instrument in the Panel:Install the instrument from behind the instrument panel using 6 x 32 screws. These screws must not be anylo

F. (FP-5L Only) Check the FP-5L display to read a number when the "F. to D." (Fuel to Destination) buttonis pushed. You may have to fly th

Fuel Flow/Pressure (FP-5 and FP-5L) Wiring Diagram116' Red Wire6' Black Wire6' White WireRedBlackWhiteAUX Channel Input Lines. See the

FP-5(L) / FFDM-1 Interconnect Wiring Diagram12Circular Connec-tor6' Red Wire6' Black Wire6' White WireRedBlackWhiteFuel Flow Differenti

13FP-5 and FP-5L Circular Connector1 and 2 connect to powerand ground.637101114151621Blk RedW/YelW/BrnW/RedW/OrgW/RedWhtW/YelWht Blk Red7 through 9 co

314796Connecting Cable Harness, Back View (wire side)Module Connector, Front ViewORBlk RedW/BlkW/Red14FFDM-1 Circular ConnectorNote: See Wiring Diagra

15Specifications and Operating FeaturesModel:FP-5 and FP-5L (Fuel Flow/Pressure Instrument)Case Dimensions:2.5" x 2.5" x 3.65" depth, 2

Max Displayed Range (Unit Only):Fuel Flow: 199.9 Gals/Hr or 162.0 br Gal/Hr or 1199 Lbs/Hr or 749 Ltr/Hr.Fuel Remaining: 999 Gals. or 811 br Gal. or 1

Drawn By:Electronics International Inc.Approved By:Scale:Material:Next Assembly:P/N: Date: Rev: D/N:12/29/931229931R.R.R.R.NoneInstallation of a Fuel

Important Notice***** MUST READ *****If you think it is not important to read this manual, you're wrong! This manualcontains important installat

Drawn By:Electronics International Inc.Approved By:Scale:Material:Next Assembly:P/N: Date: Rev: D/N:12/29/93R.R.R.R.NoneInstallation of a Fuel Flow Tr

Drawn By:Electronics International Inc.Approved By:Scale:Material:Next Assembly:P/N: Date: Rev: D/N:10/15/94R.R.R.R.NoneInstallation of a Fuel Flow Tr

Drawn By:Electronics International Inc.Approved By:Scale:Material:Next Assembly:P/N: Date: Rev: D/N:4/15/94R. R.R.R.NoneInstallation of the Fuel Flow

ContentsWarranty ... 21. Important Information and I

2Warranty / AgreementElectronics International Inc. (E.I. inc.) warrants this instrument and system components to be free fromdefects in materials and

FP-5 and FP-5LInstallation Instructions1. Important Information and Initial Check Out:A. The installer and aircraft owner must read the Warranty be

42. Install the Fuel Flow Transducer:Mount the Fuel Flow Transducer using the appropriate drawing at the back of this manual. The instructions list

5D. The flow transducer must be mounted so the wires exiting the transducer are pointing up.E. Before connecting any hoses, thoroughly clean them an

65. Route the Power and Ground Wires:In the wire harness are two sets of red and black 6' wire bundles used for the fuel pressure transducer and

Any excess wires can be rolled up and tie wrapped under the instrument panel. Tie wrap these wires so theydo not obstruct the freedom of travel of an